WEATHERSEALS: PRICELIST

WS02 is a 5/32” (4mm) diameter silicone tubeseal designed to be glued into the corner of a wood or metal jamb with silicone caulk.  Use it on stops, rabbeted jambs, and astragals where gaps measure 0 – 1/8” (0 – 3mm).  Solvent clean the jambs, apply a small bead of silicone caulk, press the seal into the wet caulk, and roll it with WS96. WS02 is available in bronze or white in 100 ft rolls or cut to any length.

100 ft rolls - $36.00
cut to length - $0.72/ft

WS03 is a 7/32” (5.5mm) diameter silicone tubeseal designed to be glued into the corner of a wood or metal jamb with silicone caulk.  Use it on stops, rabbeted jambs, and astragals where gaps measure 1/16” – 3/16” (2mm – 5mm).  Solvent clean the jambs, apply a small bead of silicone caulk, press the seal into the wet caulk, and roll it with WS96.  WS03 is available in bronze or white in 100 ft rolls or cut to any length.

100 ft rolls - $44.00
cut to length - $0.88/ft

WS04 is a 9/32” (7.5mm) diameter silicone tubeseal designed to be glued into the corner of a wood or metal jamb with silicone caulk.  Use it on stops, rabbeted jambs, and astragals where gaps measure 1/8” – 1/4” (3mm – 6mm).  Solvent clean the jambs, apply a small bead of silicone caulk, press the seal into the wet caulk, and roll it with WS96.  WS04 is available in bronze or white in 100 ft rolls or cut to any length.

100 ft rolls - $54.00
cut to length - $1.08/ft

WS05 is a 11/32” (9mm) diameter silicone tubeseal designed to be glued into the corner of a wood or metal jamb with silicone caulk. Use it on stops, rabbeted jambs, and astragals where gaps measure 3/16” – 5/16” (5mm – 8mm). Solvent clean the jambs, apply a small bead of silicone caulk, press the seal into the wet caulk, and roll it with WS96.  WS05 is available in bronze or white in 100 ft rolls or cut to any length.

100 ft rolls - $64.00
cut to length - $1.28/ft

WS06 is a 13/32” (10.5mm) diameter silicone tubeseal designed to be glued into the corner of a wood or metal jamb with silicone caulk. Use it on stops, rabbeted jambs, and astragals where gaps measure 1/4” – 3/8” (6mm – 10mm). Solvent clean the jambs, apply a small bead of silicone caulk, press the seal into the wet caulk, and roll it with WS96.  WS06 is available in bronze or white in 100 ft rolls or cut to any length.

100 ft rolls - $72.00
cut to length - $1.44/ft

WS10 is a 1/4” (6mm) diameter silicone tubeseal designed to be compressed to 5/32” (4mm).  It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40 or WS42.  Use it for compression sealing, such as in applied stops of hinged windows and doors, or in the top and bottom edges of double-hung windows.  WS10 is available in black, brown, gray, or white in 164 ft rolls or cut to any length.

164 ft rolls - $120.00
cut to length - $1.12/ft

WS11 is a 3/8” (10mm) diameter silicone tubeseal designed to be compressed to 1/4” (6mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40. Use it for compression sealing, such as in applied stops or rabbeted jambs of hinged windows or doors, or in the top and bottom.  WS11 is available in black, brown, gray, or white in 164 ft rolls or cut to any length.

164 ft rolls - $204.00
cut to length - $1.92/ft

WS12 is a 1/4” (6mm) silicone flipperseal designed to be compressed to 5/32” (4mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40 or WS42. This is an ideal seal for use in applied stops of hinged windows or doors (WS14 or WS15 are preferable for rabbeted jambs because they seal a wider range of gaps).  WS12 is available in black, brown, gray, or white in 164 ft rolls or cut to any length.

164 ft rolls - $142.00
cut to length - $1.32/ft

WS14 is a 1/2” (13mm) heavy-duty silicone flipperseal designed to be compressed to 1/4” (6mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40. Use it for doors with rabbeted jambs or 1/2” (13mm) applied stops. The left lip seals air flow between a stop and jamb; the right lip protects the edge of the wood from damage.  WS14 is available in black, brown, gray, or white in 164 ft rolls or cut to any length.

164 ft rolls - $284.00
cut to length - $2.60/ft

WS15 is a 1/2” (13mm) silicone offset-flipperseal designed to be compressed to 1/4” (6mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in the corner of a rabbeted door or window jamb. It can also fit into a shallow rabbet cut into the back of an applied stop, in which case it will effectively seal air flow between the stop and the jamb.  WS15 is available in black in 100 ft rolls or cut to any length.

100 ft rolls - $152.00
cut to length - $2.28

WS16 is a 1/2” (13mm) silicone inline-flipperseal designed to be compressed to 1/4” (6mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in the corner of a door or window jamb parallel to the door or window face (the jamb stock should be at least 1-1/4” thick to prevent splitting). It is also useful for sealing the meeting edge of pairs of doors or windows.  WS16 is available in black, brown, gray, or white in 164 ft rolls or cut to any length.

164 ft rolls - $280.00
cut to length - $2.56/ft

WS17 is a 1/4” (6mm) long silicone sweepseal designed to seal gaps 3/16” – 1/4” (5mm – 6mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40 or WS42. Use it for door-bottom sealing with smooth threshholds, or for other edge seals where there is sweeping motion. Do not allow the seal to bend excessively.  WS17 is available in black only in 164 ft rolls or cut to any length.

164 ft rolls - $164.00
cut to length - $1.52/ft

WS18 is a 1/2” (13mm) long silicone sweepseal designed to seal gaps 7/16” – 1/2” (11mm – 13mm). It fits a 1/8” x 1/4” (3mm x 6mm) groove cut in wood with WS90, or it can be held by WS40 or WS42. Use it for door-bottom sealing with smooth threshholds, or for other edge seals where there is sweeping motion. Do not allow the seal to bend excessively.  WS18 is available in black only in 164 ft rolls or cut to any length.

164 ft rolls - $184.00
cut to length - $1.72/ft

WS20 is a heavy-duty silicone surface flipperseal designed to seal gaps 0 – 1/4” (0 – 6mm). It presses into WS50 channel which is attached to door or window jambs. It can also be applied to a wood strip to serve as an astragal for double doors. Its wide operating range and sturdy construction make it effective for sealing all heavy-use openings.  WS20 is available in black, brown, or white in 164 ft rolls or cut to any length.

164 ft rolls - $284.00
cut to length - $2.60/ft

WS24 is a 1/2” (12mm) silicone inline-flipperseal designed to be compressed to 3/16” (5mm). It fits a 3/16” x 1/4” (5mm x 6mm) groove cut in the corner of a door or window jamb parallel to the door or window face. It is specifically designed for European-style windows and doors with rabbeted sashes and jambs.  WS24 is available in black, bronze, or white in 164 ft rolls or cut to any length.

164 ft rolls - $196.00
cut to length - $2.40/ft

WS25 is a silicone double sweepseal designed to seal door-bottom gaps from 0 – 3/8” (0 – 10mm). It can be pressed into a single WS56 channel for an inexpensive fixed seal, or can be used with two WS56 plus WS93 glides and end-caps to make a door bottom system that can be precisely adjusted in minutes while the door is in place. WS25 is available in black only in 82 ft rolls or cut to any length.

82 ft rolls - $252.00
cut to length - $4.60/ft

WS32 is a 3/16” (5mm) diameter silicone cornerseal that fits a 1/8” x 3/16” (3mm x 5mm) groove cut at a 45° angle with a WS98 Corner Grooving Machine using a WS99 spiral router bit. Use it on rabbeted jambs and astragals where both the face and edge clearances measure 0 – 1/8” (0 – 3mm). Roll with WS96 to assure proper insertion. WS32 is available in black, bronze, or white in 100 ft rolls or cut to any length.

100 ft rolls - $52.00
cut to length - $1.04/ft

WS33 is a 1/4” (6mm) diameter silicone cornerseal that fits a 1/8” x 3/16” (3mm x 5mm) groove cut at a 45° angle with a WS98 Corner Grooving Machine using a WS99 spiral router bit. Use it on rabbeted jambs and astragals where both the face and edge clearances measure 1/16” – 3/16” (2mm – 5mm). Roll with WS96 to assure proper insertion. WS33 is available in black, bronze, or white in 100 ft rolls or cut to any length.

100 ft rolls - $56.00
cut to length - $1.12/ft

WS34 is a 5/16” (8mm) diameter silicone cornerseal that fits a 1/8” x 3/16” (3mm x 5mm) groove cut at a 45° angle with a WS98 Corner Grooving Machine using a WS99 spiral router bit. Use it on rabbeted jambs and astragals where both the face and edge clearances measure 1/8” – 1/4” (3mm – 6mm). Roll with WS96 to assure proper insertion. WS34 is available in black, bronze, or white in 100 ft rolls or cut to any length.

100 ft rolls - $60.00
cut to length - $1.20/ft

WS35 is a 3/8” (9mm) diameter silicone cornerseal that fits a 1/8” x 3/16” (3mm x 5mm) groove cut at a 45° angle with a WS98 Corner Grooving Machine using a WS99 spiral router bit. Use it on rabbeted jambs and astragals where both the face and edge clearances measure 3/16” – 5/16” (5mm – 8mm). Roll with WS96 to assure proper insertion. WS35 is available in black, bronze, or white in 100 ft rolls or cut to any length.

100 ft rolls - $74.00
cut to length - $1.48/ft

WS36 is a 7/16” (11mm) diameter silicone cornerseal that fits a 1/8” x 3/16” (3mm x 5mm) groove cut at a 45° angle with a WS98 Corner Grooving Machine using a WS99 spiral router bit. Use it on rabbeted jambs and astragals where both the face and edge clearances measure 1/4” – 3/8” (6mm – 10mm). Roll with WS96 to assure proper insertion. WS36 is available in black, bronze, or white in 100 ft rolls or cut to any length.

100 ft rolls - $86.00
cut to length - $1.72/ft

WS39 Offset Foam Flipperseal fits a 1/8” x 3/8” (3mm x 10mm) groove cut in the corner of a rabbeted door jamb and is designed to be compressed to 3/8” (9mm). It consists of urethane foam encased in a tough UV-resistant plastic skin and offers a low-cost alternative to WS14 or WS15 for production door shops. WS39 is available in black, bronze, or white in lengths of 7 ft or 8 ft.

7 ft - discontinued
8 ft - discontinued
20 x 7 ft - discontnued
20 x 8 ft - discontinued    

WS40 aluminum channel fits a 3/16” x 5/16” (5mm x 8mm) groove. It is most often used to mount WS62, WS64, and WS66 nylon brushes or WS17 and WS18 silicone sweeps in door bottoms. However, it can also be used to increase the pullout resistance of WS10, WS11, WS12, or WS14 and strengthen the wood in abusive environments. WS40 is available in mill finish only in lengths of 3 ft, 3.5 ft, 4 ft, 7 ft, or 8 ft.

3 ft - $3.60
3.5 ft - $4.40
4 ft - $4.80
7 ft - $8.40
8 ft - $9.20

WS42 is an attractive, low-profile, surface-mounted aluminum channel that snaps onto invisible delrin clips. Sufficient clips and wood screws are included; screws for mounting on metal jambs or doors are available on request. It can be used with WS10 or WS12 for door jambs, as well as with WS17, WS18, WS62, WS64, or WS66 for door bottoms. WS42 is available in mill finish in lengths of 3 ft or 7 ft.

3 ft - discontinued
7 ft - discontinued

WS50 aluminum channel holds WS20 in order to make a surface-mounted jamb or astragal seal on a wood door or window. The channel is supplied predrilled for special screws designed to be driven in with a hammer using our WS94 insertion tool and a nailset. The screws are included, but the insertion tool must be ordered separately. WS50 is available in mill finish only in lengths of 3 ft, 4 ft or 7 ft.

3 ft - $3.60
4 ft - $4.60
7 ft - $8.20

WS56 aluminum channel is used to hold WS25 double sweepseal. WS56 is available in mill or clear anodized versions in lengths of 3 ft, 3.5 ft, 4 ft, or 7 ft.  For fixed mounting, screw a mill or anodized WS56 channel into a 5/8” groove and insert the WS25. For adjustable mounting, screw an anodized WS56 channel into a deeper groove, insert the WS25 into a second anodized WS56 channel, and suspend the second channel from the first with WS93 glides.

3 ft - $5.40 (mill), $7.20 (anodized)
3.5 ft - $6.40 (mill), $8.20 (anodized)
4 ft - $7.20 (mill), $9.20 (anodized)
7 ft - $12.60 (mill), $16.40 (anodized)

WS58 automatic door bottom is used with WS17, WS18, WS62, WS64, or WS66 (weatherseals not included) to create a retractable door bottom system. The mechanism is screwed into a 3/4" groove. WS58 is available in 4" increments in length from 24" to 48": up to 4" can be cut off each size.

24" - $54.00
28" - $56.00
32" - $58.00
36" - $60.00
40" - $62.00
44" - $64.00
48" - $66.00
52" - $68.00
Hinge-Side End Cap (brown or white) - $0.60
Latch-Side End Cap (brown or white) - $0.60
Push Plate (brown or white) - $0.40
Mounting Screw (stainless steel, 3 required) - $0.05

WS62 is a superior-quality nylon brushseal designed for sealing rough threshholds and for heavy-duty sliding applications. It must be mounted in WS40 or WS42. If WS40 is glued flush with the wood surface, then WS62 seals gaps 3/16” – 1/4” (5mm – 6mm). If WS40 is made adjustable with WS92 screws, WS62 seals gaps 0 – 1/4” (0 – 6mm). WS62 is available in black only in in lengths of 3 ft, 3.5 ft, 4 ft, 7 ft, or 8 ft.

3 ft - $8.80
3.5 ft - $9.80
4 ft - $10.80
7 ft - $19.60
8 ft - $21.60

WS64 is a superior-quality nylon brushseal designed for sealing rough threshholds and for heavy-duty sliding applications. It must be mounted in WS40 or WS42. If WS40 is glued flush with the wood surface, then WS64 seals gaps 7/16” – 1/2” (11mm – 13mm). If WS40 is made adjustable with WS92 screws, WS64 seals gaps 1/4” – 1/2” (6mm – 13mm). WS64 is available in black only in lengths of 3 ft, 3.5 ft, 4 ft, 7 ft, or 8 ft.

3 ft - $8.80
3.5 ft - $9.80
4 ft - $10.80
7 ft - $19.60
8 ft - $21.60

WS66 is a superior-quality nylon brushseal designed for sealing rough threshholds and for heavy-duty sliding applications. It must be mounted in WS40 or WS42. If WS40 is glued flush with the wood surface, then WS66 seals gaps 11/16” – 3/4” (17mm – 19mm). If WS40 is made adjustable with WS92 screws, WS66 seals gaps 1/2” – 3/4” (13mm – 19mm). WS66 is available in black only in lengths of 3 ft, 3.5 ft, 4 ft, 7 ft, or 8 ft.

3 ft - $8.80
3.5 ft - $9.80
4 ft - $10.80
7 ft - $19.60
8 ft - $21.60

WS70 is an adhesive-backed polypropylene pile brushseal 1-1/4” wide by 1/4” thick (32mm x 6mm). It is primarily used to make a transition between door bottom seals and jamb seals, blocking air flow at the bottom corners. To use it, simply cut two small pieces and adhere them to the jambs just inside the stops at the bottom left and right corners of the door. WS70 is available in white or bronze cut to any length.

cut to length - discontinued

WS74 consists of a polypropylene pile brushseal with a flexible center fin, bonded to a hard plastic base. It fits a 1/8” x 1/4” (3mm x 6mm) groove that can be cut with WS90. WS74 seals 1/8” (3mm) gaps and is ideal for sliding seals in new sliding and double-hung windows where the gap between the window face and the stop is constant. WS74 is available in black, gray, and white in 500 ft rolls, 100 ft rolls, or cut to any length.

500 ft rolls - $180.00
100 ft rolls - $56.00
cut lengths - $0.72/ft

WS75 consists of a polypropylene pile brushseal with a flexible center fin, bonded to a hard plastic base. It fits a 1/8” x 1/4” (3mm x 6mm) groove thatcan be cut with WS90. WS75 seals 5/32” (4mm) gaps and is ideal for sliding seals in new sliding and double-hung windows where the gap between the window face and the stop is constant. WS75 is available in black, gray, and white in 500 ft rolls, 100 ft rolls, or cut to any length.

500 ft rolls - $184.00
100 ft rolls - $58.00
cut lengths - $0.76/ft

500 ft rolls - $188.00
100 ft rolls - $60.00
cut lengths - $0.80/ft

WS77 consists of a polypropylene pile brushseal with a flexible center fin, bonded to a two-component plastic base. It fits a 1/8” x 1/4” (3mm x 6mm) groove that can be cut with WS90. WS76 seals 7/32” (5.5mm) gaps and is ideal for sliding seals in new sliding and double-hung windows where the gap between the window face and the stop is constant. WS77 is available in black, gray, and white in 500 ft rolls, 100 ft rolls, or cut to any length.

500 ft rolls - $192.00
100 ft rolls - $62.00
cut lengths - $0.84/ft

500 ft rolls - $196.00
100 ft rolls - $64.00
cut lengths - $0.88/ft

WS83 is a general-purpose, straight plastic leafseal that fits a 5/64” x 5/16” (2mm x 8mm) groove cut with WS90 and seals gaps 1/16” – 1/4” (2mm – 6mm). It is usually used for edge seals in sliding windows and doors, particularly for old work where gaps may vary considerably and surfaces may be rough from many layers of paint. WS83 is available in black, gray, tan, and white in lengths of 4 ft or 8 ft.

4 ft - discontnued
8 ft - discontnued
50 x 8 ft - discontnued

WS84 is a general-purpose straight plastic leafseal that fits a 5/64” x 5/16” (2mm x 8mm) groove cut with WS90 and seals gaps 1/16” – 3/16” (2mm – 5mm). It is usually used for center and edge seals in sliding windows and doors, particularly for old work where gaps may vary considerably and surfaces may be rough from many layers of paint. WS84 is available in black, gray, tan, and white in lengths of 4 ft or 8 ft.

4 ft - discontnued
8 ft - discontnued
50 x 8 ft - discontnued

WS85 is an offset plastic leafseal that fits a 5/64” x 5/16” (2mm x 8mm) groove cut with WS90 and seals gaps 1/16” – 1/8” (2mm – 3mm). It is usually used for center and edge seals in sliding windows and doors, particularly for old work where gaps may vary considerably and surfaces may be rough from many layers of paint. WS85 is available in black, gray, tan, and white in lengths of 4 ft or 8 ft.

4 ft - discontnued
8 ft - discontnued
50 x 8 ft - discontnued 

WS86 is an offset plastic leafseal that fits a 5/64” x 5/16” (2mm x 8mm) groove cut with WS90 and seals gaps 1/16” – 3/16” (2mm – 5mm). It is usually used for center and edge seals in sliding windows and doors, particularly for old work where gaps may vary considerably and surfaces may be rough from many layers of paint. WS86 is available in black, gray, tan, and white in lengths of 4 ft or 8 ft.

4 ft - discontnued
8 ft - discontnued 
50 x 8 ft - discontnued

WS87 is an offset plastic leafseal that fits a 5/64” x 5/16” (2mm x 8mm) groove cut with WS90 and seals gaps 1/16” – 1/4” (2mm – 6mm). It is usualy used for center and edge seals in sliding windows and doors, particularly for old work where gaps may vary considerably and surfaces may be rough from many layers of paint. WS87 is available in black, gray, tan, and white in lengths of 4 ft or 8 ft.

4 ft - discontnued
8 ft - discontnued
40 x 8 ft - discontnued 

WS90 custom-made, ball-bearing-guided, four-wing, slot-cutting router bits cut the exact grooves required for many of our weatherseals without the need for a guide fence to limit the depth of cut. A top-mounted bearing makes it possible to groove rabbeted jambs. Order the 2mm x 8mm version for WS83, WS84, WS85, WS86,or WS87; order the 3mm x 6mm size for WS10, WS11, WS12, WS14, WS17, WS18, WS74, WS75, WS76, WS77, or WS78.

2mm x 8mm - discontinued
3mm x 6mm - $43.60

WS93 glides and end-caps are used to make an adjustable door bottom system using WS25 silicone sweepseal and two WS56 aluminum channels. The glide is threaded into the WS56 channel that holds the WS25, and the end caps slip into the fixed channel to conceal the groove. Order at least one glide per foot of door width, more if the threshhold is uneven. End caps are available in white, gray, or bronze.

glides - $4.20 each
end caps - $0.40 each

WS96 is a nylon-wheel roller tool recommended for pushing WS02,03,04,05,06 into wet silicone caulk and for inserting WS32,33,34,35,36 into a groove cut with WS98 corner grooving machines. It also speeds installation of WS16 (roll against the small “shoulder” in the rubber) and WS25 (roll in one “ear” of WS25 after the other ear has been inserted).

$16.00

WS98 corner-grooving machine cut a groove at a 45° angle in the corner of a door or window jamb into which WS32,33,34,35,36 tubeseals are inserted. We offer
a kit that includes a motor, tool body, vacuum hose with
1-1/4” and 2-1/4” hose fittings, and a carrying case. It features a tough plastic body with a replaceable aluminum alloy base and a high-speed motor.

$380.00

WS99 spiral router bits are used with WS98 to cut 1/8” wide grooves required for WS32, WS33, WS34, WS35, and WS36 corner tubeseals. Carbide bits are considerably more durable than high-speed steel, especially for use with painted woodwork. Do not substitute other carbide bits: standard carbide spiral router bits are too short for WS98!

high-speed steel - $12.20
carbide - $20.60